S&A 3000TG Thermolysis Industrial Water Chiller for CO2 Glass Tube of Engraving Machine, AC 1P 220-240V, 50Hz

Arrival in 2-5 business days.

Item Code: CW-3000TGTY-US


Unit Price: $219.90/set

Apply to See Distributor Price

set(s) Total Cost:  $219.90
Buy It Now Add to Cart Ask A Question

Buyer Protection

S&A 3000TG Thermolysis Industrial Water Chiller for CO2 Glass Tube of Engraving Machine, AC 1P 220-240V, 50Hz
Buy It Now


We are authorized as "S&A" brand name product agent.
All of S&A water chillers are certified with design patent. Counterfeiting is not allowed,
Please recognize S&A logo when you purchase S&A water chillers.


S&A CW-3000 series thermolysis type water cooler has compact design,with energy saving,high cost performance,good protection and alarm system.
This Water Chiller has been sold largely to Europe, South America, Asia and other markets;
Economic cooling equipment, easy to install and operate, compact and easily movable.

Remarks: CW3000 water chillers are equipped high speed fans inside, NOT able to control the water temperature. Please confirm before place an order. The products are nonrefundable after selling, only if quality issue.

 Used for:

It is designed for cooling the one CO2 glass laser tube under 80W of the laser engraving and cutting machine. (Its emitting rate is lower than 60%, you can choose CW5000 water Chiller if you want the emitting rate higher than 60 %.)
  • Specific disconnection alarm securing protection;
  • High cost performance, low failure rate;
  • Radiating Capacity is 50W / ℃;
  • Forces circulation, 9L cooling tank capacity;
  • It can extend the using life of laser tube and ensure the engraving effect better.
  • Comprehensive reference to the international radiator - type cooling system;
  • Small thermolysis water cooler;
  • With completed water flow and over high temperature alarm functions;
  • Professional forced air - cooled radiator;
  • CW-3000 Laser Water Chiller is suitable for small water cooling device;
  • Provide stable working conditions for laser devices;
  • High heat dissipating capacity and not easy to be blocked.


Model CW-3000TGTY
Voltage AC 1P 220~240V
Frequency 50/60Hz
Current 0.4~0.7A
Machine power 0.07kW
Radiating capacity 50W/℃
Pump pressure 1bar
Max.flow 10L/min
N.W 9Kgs(19.8lb)
G.W 11Kgs(24.3lb)
Protection flow alarm
Tank capacity 9 L
Inlet and outlet OD 10mm barbed connector
Dimension 490mm x 270mm x 380mm (19.3" x 10.6" x 15")
Package dimension 550mm x 340mm x 430mm (22" x 13.4" x 17")


Independent production of sheet metal and heat exchanger . 9L cooling tank, fast cooling.
Adopt IPG fiber laser for welding and cutting sheet metal, adopt minimize risks of water and refrigerant leakage and improve quality 

Ease of moving and water filling.
The firm handle can help move the water chillers easily.
Inlet and outlet connector equipped. Multiple alarm protection.
The laser will stop working once it receives alarm signal from the water chiller for protection purpose.
High speed fan of famous brand installed.
Adopt SAN JU brand from Taiwan with quality assurance and low failure rate.
Easy water draining
It is suggested to replace the cooling water(distilled water or purified water as cooling water) every 3 to 6 months.

Connection diagram between water chiller and laser machine

Water outlet of the water tank connects to water inlet of the laser machine while water inlet of the water tank connects to water outlet of the laser machine. Aviation connector of the water tank connects to the aviation connector of the laser machine.


In order to guarantee the equipment will not be damaged while cooling water circulation is out of control, CW-3000series water cooler possess a low flow alarm protection.

(1) Flow alarm output ports and the wiring diagram


Causes of the cooling water circulation alarm and the working condition table

Note: The flow alarm is connected to the normally open relay and normally closed relay contacts, requiring operating current less than 5A, working voltage less than 300V.


Method of exchanging water in the water tank and the exchanging frequency

Method of exchanging water in the water tank

Drain the waste water out of the water tank through the drain outlet and fill the clean water into the tank through the filling hole

Exchanging Frequency

The purified water should be exchanged once a month and the running water should be exchange twice a month. The quality of the circulating water will directly influence the service life the laser tube.It is recommended to use purified water.


S&A CW-3000 chiller for 3KW CNC spindle machine

S&A CW-3000 water cooler for 60W co2 laser machine

S&A CW-3000 chiller for dual 1.5KW engraving machine

S&A CW-3000 chiller for 80W co2 laser cutting machine

S&A CW-3000 chiller for acrylic laser cutting machine



With 11 patent certificates and won Quality integrity Level A certificate;  ISO 9001, CE, RoHS and REACH environmental certificated. Conforms to air transport requirements, energy saving and environment friendly.


18,000 square meters brand new industrial refrigeration system research center and production base ,Strictly execute ISO production management system, using mass modularized standard produces, and standard parts rate up to 80% which are the source of quality stability.
Annual production capacity of 60,000 units, focus on large, medium and small power chiller production and manufacture.

Test System

With excellent laboratory testing system, simulates actual working environment for chiller. Overall performance testing before delivery: aging test and complete performance test must be executed on each finished chiller.


It is very simple to install this industrial cooling machine. The first time installation of the new machine can be carried out by following steps.

Open the package to check if the machine is intact and all the necessary accessories are completed.


Open the injection port to feed cooling water. (Do not let the water spill over!)


According to system conditions, please connect the water inlet and outlet pipe well.


Plug in power, turn on the power switch. (Do not start up without water in the water tank!)

(1) Power switch turned on, the circulation pump of the chiller starts working. The first time of operating may cause more bubbles in the pipe leading to a flow alarming occasionally, but running for a few minutes later, it will go back to normal.
(2) After the first boot, you must immediately check whether the water pipe leaks.

Check the water level of the water tank again. (It should be 80-150cm from the surface of water to the injection port)




Please ensure that the power supply and electrical outlet are in good contact and the earth wire must be firmly grounded!


Please make sure there is stable and normal voltage for the working chiller!

As the refrigeration compressor is more sensitive to the power supply and voltage, so the operating voltage of our standard product is of 210 ~ 240V (110V model is of 100 ~120V). If you do need a wider operating voltage range, customization is available for us.

Unmatched power frequency can cause the chiller damage!

Please choose model of 50Hz or 60Hz according to actual circumstance.

To protect the pump, it’s strictly forbidden to run the chiller without water in the storage water tank!

The new machine is packed after draining whole water in the tank, so please make sure the tank has water inside before machine starting, otherwise it’s easily to have the pump damaged.
To drain through circulating pump is strictly prohibited!

Please be sure that the air inlet and air outlet are in good ventilation!

There must be at least 30cm from obstructions to the air outlet which is in the back of the cooler, and should leave at least 8cm between obstructions and the side air inlet.

The cooling water must be drained if the cooler is out of use for long time or before being transported.

To protect laser heating devices , the radiator fan of cooler will suspend to work when water temperature is lower ( about 10℃ ) , and it will restart to run when water temperature rises to higher ( about 20 ℃).


Failure Failure Cause Approach
Machine turned on but unelectrified
Power cord is not plugged in place fuse burnt-out
Plug the power cord in place Replace the fuse inside the power interface which is in the back of machine
Flow alarm (panel red light) with water pipe directly connect to the outlet, inlet, there is no water flow Water level in the storage water tank is too low Feed water and check the pipe leakage
When used with the device, flow alarm (panel red light), but a direct connection with the pipe outlet and inlet, there is water flowing but not alarming Blockage in circulating water pipeline Check circulating water pipeline
Ultra-high temperature
Chiller of poor ventilation Excessive heat load
To improve the ventilation Reduce the heat load or to use other models
A normal boot, but the fan does not work The water temperature below 20 degrees A normal phenomenon, no processing
Switch on with alarming after adding water or changing water
Water drop in electric circuit Damaged pumps dry transfer
Natural drying or drying off cap To replace or repair water pumps,prohibited anhydrous boot
Slow outfall drainage The injection port is not open Open the injection port

Model CW-3000TGTY
Voltage AC 1P 220~240V
Frequency 50/60Hz
Current 0.4~0.7A
Machine power 0.07kW
Radiating capacity 50W/℃
Pump pressure 1bar
Max.flow 10L/min
N.W 9Kgs(19.8lb)
G.W 11Kgs(24.3lb)
Protection flow alarm
Tank capacity 9 L
Inlet and outlet OD 10mm barbed connector
Dimension 490mm x 270mm x 380mm (19.3" x 10.6" x 15")
Package dimension 550mm x 340mm x 430mm (22" x 13.4" x 17")

Wooden Box: There is total one carton box. 

Machine Dimension 490mm x 270mm x 380mm (19.3" x 10.6" x 15")
Machine Weight 9Kgs(19.8lb)
Package Carton box
Packing Size 550mm x 340mm x 430mm (22" x 13.4" x 17")
Gross Weight 11Kgs(24.3lb)

Caution: The appliance is not to be used by children or persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge, unless they have been given supervision or instruction, children supervised not to play with the appliance!



CW 3000 Water Chiller

Agent  Certificate of  Authorization

User Manual for CW-3000 Series Water Chiller

Comprehensive guarantee for 2 years except the wearing parts.
24 - hour technical support by email or calling.
English user manual for machine using and maintaining.

Spare Parts Supports
We provide all replacement parts for all machines we sold, if you have a parts that break beyond warranty period, you could order it directly from us at reasonable prices. We would post the new parts with step by step instructions in PDF format on how to replace the parts to you.
If you want to buy any parts from us, please tell us the names or pictures of the parts.

Satisfaction Guarantee
For the items other than consumable products sold via www.Sign-in-China.com, we provide 24 months warranty after shipment. All the extra parts for equipment can be purchased from www.Sign-in-China.com. 

We offer 14 days 100% satisfaction guarantee on all our machines. If you are not satisfied after receiving an item, Sign-in-China.com promises that, within 14 days after actual delivery of such an item, you are allowed to return the item to us and get complete refund, provided the returned item does not affect its subsequent re - selling and you also undertake the charge of returning delivery.

More information, please look at the document of Training & Warranty & Service Policies. 
Training & Warranty & Service Policies

Customer Reviews
Love it! Rate it!
  • Simply write a review of a product and you can get up to 500 Points (Equivalent to $5) for Next Orders.
  • ≥ 120 words + ≥ 3 clear photos = Up to 1000 Points (Equivalent to $10).
  • Show us why you love or how to use the product. Help other shoppers find the right product!
Average Rating: 0

Ask A Question for S&A 3000TG Thermolysis Industrial Water Chiller for CO2 Glass Tube of Engraving Machine, AC 1P 220-240V, 50Hz

Select a topic: Item Description Shipping Payment Other

Preview Size State Operation

Verification code:

  • Reviews (0)
  • Questions (0)
  • No Reviews
Top Selling

Get in Touch

9850 6th St Rancho Cucamonga CA 91730




Subscribe to our special offers

Follow us

Follow us on Facebook Follow us on Youtobe
Back to top